Install Sony XAV-AX5000 for 2013 Honda CR-V EX-L (No Navigation version) First at all, Whenever you mess with car electronics, the first thing you need to do is to remove the negative terminal of your car’s battery,the best is remove both negative and positive. Disclaimer： all operations may be risky, so please ask professional do it or bear your own risk!! We are not responsible for any risks or responsibilities!! what will needs: SONY XAV-AX5000 Scosche LPHA15 (Honda LINK+ Interface with Steering Wheel Control Retention) Scosche HA1714B ( 2012-Up Honda CRV ISO Double DIN & DIN+Pocket Dash Kit) Scosche HAA2B ( 2010-Up Honda Antenna Adapter) Electrical Tape + Electrical Industrial and Electrical Harness Wiring Friction Tape you need screwdriver and may need Car Panel Removal Tool too RCA Cable 1. Take the old Head unit out https://www.youtube.com/watch?v=MtTw4DURgGw 2. connect the cable from SONY AX5000 with Scosche LPHA15,it is basically matching the color of the cables together,and taped them. 3. Connect the SONY AX5000 to CR-V (three connectors need to connect,left the white color one,because the SONY AX5000 has not connector match it. ),next you will need to remove the OEM Bluetooth connector from the Bluetooth Module and plug the Bluetooth connector from Scosche LPHA15 to bypass the module. (the OEM Bluetooth Module’s location under the shift lever,part number 39775-T0A-A50),connect this Bluetooth then can you setup up the make call, hand up,voice buttons of the steering wheel control on SONY AX5000. Once open the panel and bezel,you will see the Bluetooth Module inside like this following: Now you will be able to set up the custom streering wheel control setting on SONY AX5000!! At this point,the Rear View Camera still not shows on SONY AX5000 yet, you will need to spliting the Video cable from the Upper iMID small Display to connect to SONY AX5000,let’s do it!! To spliting a connector to SONY AX5000 from iMID Display. you will need a RCA cable, cut the RCA cable and get the wires ready, then tape the Vidoe Center wire to Pin#19 and the Ground wire to #18 from the 32 Pin Connector as picture above,final connect the RCA connector to SONY AX5000, Done! As the picture follow, the #1 will connect to Pin#19, #2 will be connect to Pin#18!! Here is the information posted by jacan20 from CRV Owner Club (Thanks so much for the information) “I cut off one of the ends of the rca cable and stripped away some of the insulation. A rca video cable is comprised of a center cable (video positive) that is surrounded by many very thin ground wires. These ground wire are very fragile and annoying to work with; be very careful with them! Carefully twist only the ground wires together and crimp a male plug of a t-tap on it. Crimp another male end onto the center data positive wire. Inside the car, attach the female part of a t-tap onto the wire that leads to pin 18. Attach another […]
To wipe and convert the drive by using Windows Setup Turn off the PC, and put in the Windows installation DVD or USB key. Boot the PC to the DVD or USB key in UEFI mode. For more info, see Boot to UEFI Mode or Legacy BIOS mode. When choosing an installation type, select Custom. On the Where do you want to install Windows? screen, select each of the partitions on the drive, and select Delete. The drive will show a single area of unallocated space. Select the unallocated space and click Next. Windows detects that the PC was booted into UEFI mode, and reformats the drive using the GPT drive format, and begins the installation. To manually wipe a drive and convert it to GPT: Turn off the PC, and put in the Windows installation DVD or USB key. Boot the PC to the DVD or USB key in UEFI mode. For more info, see Boot to UEFI Mode or Legacy BIOS mode. From inside Windows Setup, press Shift+F10 to open a command prompt window. Open the diskpart tool: diskpart Identify the drive to reformat: List disk Select the drive, and reformat it: select disk 0 —- 0 is the disk you want to format clean convert gpt ( convert mbr if you want to bmr format) exit Close the command prompt window. Continue the Windows Setup installation. When choosing an installation type, select Custom. The drive will appear as a single area of unallocated space. Select the unallocated space and click Next. Windows begins the installation.
2018 FIRMWARE CMU UPDATE PROCEDURE-WORLDWIDE https://techblog.jeppson.org/wp-content/uploads/2019/02/2018-FIRMWARE-CMU-UPDATE-PROCEDURE-WORLDWIDE.pdf Files needs: https://drive.google.com/file/d/1bbLmJ57XL8TqhCsw4rJ0zfta9GjVM9yL/view?usp=sharing Installing Android Auto / Apple Carplay retrofit in Mazda CX3
R.I.P. Kobe Bryant dies in California helicopter crash on 01-26-2020 Kobe’s 13 years-old daughter Gianna Maria was also on board the helicopter and died in the crash. Kobe Bryant will FOREVER be a legend to all of us!!
Warning, this will voids the warranty. Also make sure you backed up what you need to because it will wipe all your device clean! 注意： 这操作会让保修失效，请慎重操作，还有记得保存手机数据，这操作会抹除手机所有数据！！ This method works on LG G6 H872 T-Mobile US version. Files : Download adb-Tool and Unzip to anywhere you can find,for example I unzipped the files to D: 下载adb-tool 和解压 Go to the Phone’s Settings>General > About > Software info>Build number press 6 times> go back to General and find developer options>Enable OEM Unlock On, and Enable usb debugging. Connected the Phone to Computer with Cable(Tap ok or give access if the phone ask or request) Open the cmd.exe (the cmd.exe you can find it where you unzipped to) Enter: adb reboot bootloader (if the phone ask for Allow USB debugging?, click and Tap Ok) — The Phone will be reboot and in Fastboot Mode. 6.enter: fastboot oem unlock the phone will shows as this 7. After than it should unlock to verify type: fastboot getvar unlocked and it will say yes or no! 8. enter: fastboot reboot （The Phone will be reboot to normal mode)） and you’ll be all in! To relock the bootloader: adb reboot bootloader fastboot oem lock To verify your status type: fastboot getvar unlocked From: https://forum.xda-developers.com
ROOT LG G6 H872 (up to and including 20g) -LG H872 Root 教程 WARNING DO NOT LET YOUR PHONE REBOOT, OR POWER OFF UNTIL I TELL YOU THAT IS WHAT YOU NEED TO DO. If you do, I am not sure what shape your phone will be in. This should go without saying, but you MUST have your bootloader unlocked ( Click H872 Bootloader Unlock if you don’t know how to unlock H872 Bootloader). If you don’t, you will probably brick your phone. If you use this on any model G6 besides the H872, you will be stuck in a bootloop, and you will not be able to fix it since you will have wiped out download mode! This is safe if no mistakes are made (typos, missing a step, etc). However, if you do mess up, the risk is high that you lose download mode at best, or brick your phone at worst. If you deviate from this procedure, and think: “I can just skip a step, or I can do this on my own Linux install”. Don’t complain if you brick your phone. PREREQUISITES: You must have a version of laf that has the COPY opcode. Since none of the firmware available for the H872 has the COPY opcode, we have to use the H918 laf partition. Grab the H918 10p KDZ: link to 10p KDZ You need to be on 11g or above. Be aware, once you are on 11g+ you cannot downgrade to any versions prior to 11g due to anti-rollback. You will need a copy of the KDZ that your phone is on. If you are not currently on 11g, upgrade before continuing.To download the KDZ firmware please go to https://lg-firmwares.com/ We are going to flash this using the patched LG UP. There may be one that was patched specifically for the G6 — don’t use it, it has NOT been tested. Grab the one for the V20: LGUP_V20dll_Patched It MUST be installed in: C:Program Files (x86)/LG Electronics/ 一定要解压LGUP文件夹到这个目录，否则不能识别!! You can’t just unzip it anywhere and run it, it will not find the model file. You need the H872 Unofficial 3.2.3 TWRP by @Eliminator74. 3.2.3 is included in the repo so that you know that you have the exact version.实际测试中，这个可以不用. You need to grab FWUL (version 2.7 or later) and burn it to a USB stick: link 这个就是FWUL U盘Linux 操作系统，用来下面输入代码安装TWRP的 Even if you have Linux, and you think you can install the dependencies, don’t. I know this works from FWUL. If you are rooting on 20a, you will need a Micro-SD card. Copy the TWRP 3.2.3 image and the latest Magisk zip to the SD card. WARNING: Only applies if rooting while on 20a Minor Encryption-related issues have occurred while testing 20a. If your data partition is encrypted, TWRP will NOT be able to decrypt it. Because of this, you will have to perform a wipe and format of your Data partition. Be sure to backup all data on your device prior to continuing by copying important files to an external SD card or […]
URL 在线网址 iCdrama.se http://www1.icdrama.to/ Watch on Smartphones 在智能手机上播放: Download RSS Player 下载一款RSS 播放器 (Download one on the App Store or Google Store 在手机应用商店下载) add the RSS link address 添加这个RSS网址 : http://allrss.se/dramas Done! View and Enjoy it! 完成！ Example for iPhone： From: iCdrama.to
Here is the Step by step Homemade Gold bread. Sweet Buns filled with tasty molten salted egg custard! Hope you enjoy this video,thank you! If you have any question,please leave message here and I will respond soon as I can. 希望你会喜欢一个视频，如果你有任何问题关于这视频的请留言，我会尽快回复，谢谢。
Here is the Step by step Homemade steamed rice rolls. Hope you enjoy this video,thank you! If you have any question,please leave message here and I will respond soon as I can. 希望你会喜欢一个视频，如果你有任何问题关于这视频的请留言，我会尽快回复，谢谢。
Here is the Step by step Homemade Taro cake. Hope you enjoy this video,thank you! If you have any question,please leave message here and I will respond soon as I can. 希望你会喜欢一个视频，如果你有任何问题关于这视频的请留言，我会尽快回复，谢谢。